SystemD scripts for Automated Startup of TIBCO MFT Command Center and Internet Server on UNIX
Article ID: KB0076677
Updated On:
| Products | Versions |
|---|---|
| TIBCO Managed File Transfer Command Center | All |
Description
MFT services can be set to start automatically after a reboot on UNIX machines. SystemD scripts can be created to facilitate this.
Environment
Tested on Linux OS
Resolution
Note: Absolute paths must be provided for variables in <>.
For TIBCO MFT Command Center
============================
1. Create a Unit file in /etc/systemd/system/ titled mftcc.service
Contents of the Unit file:
[Unit]
Description=MFT Command Center Service
[Service]
Type=oneshot
ExecStart=<MFTCC>/server/bin/startup.sh
RemainAfterExit=true
StandardOutput=journal
ExecStop=<MFTCC>/server/bin/shutdown.sh
[Install]
WantedBy=multi-user.target
2. Save the Unit file.
3. Run 'systemctl enable mftcc.service'. // enables the service to start automatically after a reboot.
4. Run 'systemctl start mftcc.service'. // starts the service
5. To check if the process is started: 'systemctl status mftcc.service'.
6. To stop the service: 'systemctl stop mftcc.service'.
Note: Steps 3 and 4 need to be performed only once, that is, after unit file creation.
Note: Absolute paths must be provided for variables in <>.
For TIBCO MFT Internet Server
=============================
1. Create a Unit file in /etc/systemd/system/ titled mftis.service
Contents of the Unit file:
[Unit]
Description=MFT Internet Server Service
[Service]
Type=oneshot
ExecStart=<MFTIS>/server/bin/startup.sh
RemainAfterExit=true
StandardOutput=journal
ExecStop=<MFTIS>/server/bin/shutdown.sh
[Install]
WantedBy=multi-user.target
2. Save the Unit file.
3. Run 'systemctl enable mftis.service'. // enables the service to start automatically after a reboot.
4. Run 'systemctl start mftis.service'. // starts the service
5. To check if the process is started: 'systemctl status mftis.service'.
6. To stop the service: 'systemctl stop mftis.service'.
Note: Steps 3 and 4 need to be performed only once, that is, after unit file creation.
For TIBCO MFT Command Center
============================
1. Create a Unit file in /etc/systemd/system/ titled mftcc.service
Contents of the Unit file:
[Unit]
Description=MFT Command Center Service
[Service]
Type=oneshot
ExecStart=<MFTCC>/server/bin/startup.sh
RemainAfterExit=true
StandardOutput=journal
ExecStop=<MFTCC>/server/bin/shutdown.sh
[Install]
WantedBy=multi-user.target
2. Save the Unit file.
3. Run 'systemctl enable mftcc.service'. // enables the service to start automatically after a reboot.
4. Run 'systemctl start mftcc.service'. // starts the service
5. To check if the process is started: 'systemctl status mftcc.service'.
6. To stop the service: 'systemctl stop mftcc.service'.
Note: Steps 3 and 4 need to be performed only once, that is, after unit file creation.
Note: Absolute paths must be provided for variables in <>.
For TIBCO MFT Internet Server
=============================
1. Create a Unit file in /etc/systemd/system/ titled mftis.service
Contents of the Unit file:
[Unit]
Description=MFT Internet Server Service
[Service]
Type=oneshot
ExecStart=<MFTIS>/server/bin/startup.sh
RemainAfterExit=true
StandardOutput=journal
ExecStop=<MFTIS>/server/bin/shutdown.sh
[Install]
WantedBy=multi-user.target
2. Save the Unit file.
3. Run 'systemctl enable mftis.service'. // enables the service to start automatically after a reboot.
4. Run 'systemctl start mftis.service'. // starts the service
5. To check if the process is started: 'systemctl status mftis.service'.
6. To stop the service: 'systemctl stop mftis.service'.
Note: Steps 3 and 4 need to be performed only once, that is, after unit file creation.
Issue/Introduction
Automated startup of MFT services after a reboot.
Was this article helpful?
Yes
No
Powered by
