SpecBuilder 6.2 generates Error text box when using the Analyzer to analyze an X12 or EDIFACT document.
Article ID: KB0093131
Updated On:
| Products | Versions |
|---|---|
| TIBCO BusinessConnect EDI Protocol Powered by Instream | - |
| Not Applicable | - |
Description
Resolution:
When using the SpecBuilder 6.2 Analyzer to process an X12 or EDIFACT document, the Analyzer may error out with the following Error text box:
XEngine component is not able to load the specified guideline.
Reason: Registry path Actions/Engine/CommitDataAction does not exist.
This error appears because of a configuration error during the installation of SpecBuilder. This can be corrected as follows:
1. Go into SpecBuilder installation directory (e.g. "C:\Program Files\Edifecs\SpecBuilder62"). In this directory, go to the Config\XEngine directory.
2. Open the XERegistry.xml file, and look for this section:
<Product Name="Actions">
<Category Name="Engine">
<Item Name="CheckTransactionEDI">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="CheckTransactionEDIFACT">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="DataTypeEDIFACT">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="DataTypeGeneric">%INSTALL_PATH%SlnEDI.dll</Item>
.
.
.
<Item Name="ExtraDelimitersHL7">%INSTALL_PATH%SlnHL7.dll</Item>
<Item Name="CommitData">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="BinaryDataAction">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="DataFilterAction">%INSTALL_PATH%SlnEDI.dll</Item>
.
.
.
3. Change the line:
<Item Name="CommitData">%INSTALL_PATH%SlnEDI.dll</Item>
to
<Item Name="CommitDataAction">%INSTALL_PATH%SlnEDI.dll</Item>
4. Save XERegistry.xml.
5. Close SpecBuilder and restart. The Analyzer should now process the document correctly.
When using the SpecBuilder 6.2 Analyzer to process an X12 or EDIFACT document, the Analyzer may error out with the following Error text box:
XEngine component is not able to load the specified guideline.
Reason: Registry path Actions/Engine/CommitDataAction does not exist.
This error appears because of a configuration error during the installation of SpecBuilder. This can be corrected as follows:
1. Go into SpecBuilder installation directory (e.g. "C:\Program Files\Edifecs\SpecBuilder62"). In this directory, go to the Config\XEngine directory.
2. Open the XERegistry.xml file, and look for this section:
<Product Name="Actions">
<Category Name="Engine">
<Item Name="CheckTransactionEDI">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="CheckTransactionEDIFACT">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="DataTypeEDIFACT">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="DataTypeGeneric">%INSTALL_PATH%SlnEDI.dll</Item>
.
.
.
<Item Name="ExtraDelimitersHL7">%INSTALL_PATH%SlnHL7.dll</Item>
<Item Name="CommitData">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="BinaryDataAction">%INSTALL_PATH%SlnEDI.dll</Item>
<Item Name="DataFilterAction">%INSTALL_PATH%SlnEDI.dll</Item>
.
.
.
3. Change the line:
<Item Name="CommitData">%INSTALL_PATH%SlnEDI.dll</Item>
to
<Item Name="CommitDataAction">%INSTALL_PATH%SlnEDI.dll</Item>
4. Save XERegistry.xml.
5. Close SpecBuilder and restart. The Analyzer should now process the document correctly.
Issue/Introduction
SpecBuilder 6.2 generates Error text box when using the Analyzer to analyze an X12 or EDIFACT document.
Feedback
Yes
No
Powered by
